DCache Administration Console Commands

About this document

• This document shows several examples of useful commands that can be run in the dCache Administration Console.
• Administration console can be accessed through [PCells GUI] or through SSHv2 as follows (in the example, dccore.pic.es is the physical machine running the admin cell):

ssh -2 -x -o StrictHostKeyChecking=no -l admin -c blowfish -p 22224 dccore.pic.es

• In this document we show what we consider the most important commands for the everyday's administration tasks, and basically the ones that may be useful for the Manager On Duty. Maybe some important commands are missing, but will be added as soon as we detect that these may be important for the MoD.
• This document is divided in two main blocks:

1. Pool commands: shows useful commands that can be run on pools.
2. Service commands: show useful commands that can be run on servers (this will include doors)

The basics

• If you access the Administration Console through SSHv2 you should access to the different cells as follows:

\? [command]...  # display help for shell commands
\c cell[@domain] [user]  # connect to cell
\exception [trace]  # controls display of stack traces
\h [command]...  # display help for cell commands
\l [cell[@domain]|pool/poolgroup]...  # list cells
\q # quit
\s (cell[@domain]|pool/poolgroup)[,(cell[@domain]|pool/poolgroup)]... command...  # send command
\sl pnfsid|path command...  # send to locations
\sn command...  # send pnfsmanager command
\sp command...  # send poolmanager command
\timeout [seconds]  # sets the command timeout

• With \s you will be able to access to any cell[@domain]s, while branches of this command such like \sn or \sp are useful to (respectively) direct access to the namespace or poolmanager cells without the need of specifying the cell[@domain].

Pool commands

Introduction

• Any command run on a pool is a temporary change: on any pool service restart configuration will be restored back to the default value or to the value set in the setup file (locate in /dcpool*/vpool*/setup).

• In example, whenever we set a pool to rdonly, on restart, once the initialization process finishes, pool will switch back to enabled.

• If you want to make permanent changes, you should save changes. Running the save command will update the already mentioned setup file.

• In example, whenever we set a pool to rdonly and we save the configuration, on a restart, once the initialization process finishes, pool will remain rdonly.

Disable / enable pools

Command help

[dccore01] (local) admin > \s dc???_? help hsm
pool disable [options] [<errorCode> [<errorMessage>]] # suspend sending 'up messages'
     OPTIONS :
       -fetch    #  disallows fetch (transfer to client)
       -stage    #  disallows staging (from HSM)
       -store    #  disallows store (transfer from client)
       -p2p-client
       -rdonly   #  := store,stage,p2p-client
       -strict   #  := disallows everything
pool enable # start sending 'up messages' again
pool suppress hsmload on|off

Disable / enable pool examples

• Disallow store + stage + p2p-client (set pool in read only mode)

[dccore01] (local) admin > pool disable -rdonly

• Enable pool (set pool to RW)

[dccore01] (local) admin > pool enable

HSM configuration

Command help

[dccore01] (local) admin > \s dc???_? help hsm
hsm create <type> [<name> [<provider>]] [-<key>=<value>] ...
hsm ls [<name>] ...
hsm remove <name>
hsm set <name> [-<key>=<value>] ...
hsm show providers # show available nearline storage providers
hsm unset <name> [-<key>] ...

HSM configuration examples

• Create a enstore HSM with the real-encp.sh client script (this example can be found in the setup file):

[dccore01] (local) admin > hsm create enstore enstore script -pnfs=/pnfs/fs/usr -command=/opt/enstore/bin/real-encp.sh -c:gets=200 -c:puts=20 -c:removes=2

• Show enstore configuration:

[dccore01] (local) admin > hsm ls enstore
enstore(enstore):script
  pnfs                /pnfs/fs/usr
  command             /opt/enstore/bin/real-encp.sh
  c:gets              200
  c:puts              20
  c:removes           2

• Set maximum restores to 400:

[dccore01] (local) admin > hsm set enstore -c:gets=400

Mover management

Command help

[dccore01] (local) admin > \s dc???_? help hsm
mover kill <jobid>  # terminate a file transfer connection
mover ls [-binary [jobId] ]
mover queue ls [-l]  # list all mover queues in this pool
mover remove [<jobid>]  # #OBSOLETE command
mover set max active [OPTIONS] <maxactivemovers>  # set the maximum number of active client transfers

Mover management examples

• Show current ftp transfers:

[dccore01] (local) admin > \s dc???_? mover ls -l -queue=ftp
33743014 : RUNNING : 0000D5B91029797545859181EB738C25E93C IoMode=READ h={SU=0;SA=0;S=None} bytes=12113543168 time/sec=3893 LM=0 si={vo-cms.cms}
33743019 : RUNNING : 00008862CFF7A1C74513A617D364A4162DAA IoMode=READ h={SU=0;SA=0;S=None} bytes=10561388544 time/sec=3409 LM=0 si={vo-cms.cms}
33743076 : RUNNING : 0000736CFC0DAF494816BFE7CC32D3192900 IoMode=READ h={SU=0;SA=0;S=None} bytes=2034630656 time/sec=2478 LM=0 si={vo-cms.cms}
33743086 : RUNNING : 0000C5F1B9D6EEC04DEEA077CA6753E30DE0 IoMode=READ h={SU=0;SA=0;S=None} bytes=488898560 time/sec=1357 LM=1 si={vo-cms.cms}
33743103 : RUNNING : 0000BBE684CB4BA44AB5ACB0D13C5DD25C8C IoMode=READ h={SU=0;SA=0;S=None} bytes=135921664 time/sec=239 LM=20 si={vo-cms.cms}

• Show all mover queue properties:

[dccore01] (local) admin > \s dc???_? mover queue ls -l
regular 0 0 0
p2p 0 40 0
ftp 11 500 0
dcap 0 10 0
nfs4 0 100 0
xrootd 406 1500 0
xrootd-wan 0 700 0
webdav 0 0 0

• Set to 400 the maximum active client transfers for the ftp queue:

[dccore01] (local) admin > \s dc???_? mover set max active -queue=ftp 400
Max Active Io Movers set to 400